---
title: Check your sensor after setup
description: Check your PlantOS sensor after setup, confirm connectivity and verify monitoring data for FitMachine, vEdge and Eqsense devices.
---

[Skip to content](https://learn.movus.com.au/knowledge/check-your-sensor-after-setup#main-content)

English

Show submenu for translations

[![Movus-horizontal-Orange-White-WT-1.png\]](https://learn.movus.com.au/hs-fs/hubfs/Movus-horizontal-Orange-White-WT-1.png?height=39&name=Movus-horizontal-Orange-White-WT-1.png)](https://movus.com.au/)

- [Contact Support](https://movus.com.au/get-in-touch/)

Open main navigation

Close main navigation

- [Contact Support](https://movus.com.au/get-in-touch/)
- English
  
  Show submenu for translations
- [Dashboard Login](https://plantos.movus.com.au/)

[Dashboard Login](https://plantos.movus.com.au/)

 Hello. How can we help you?

- There are no suggestions because the search field is empty.

1. [Knowledge Base](https://learn.movus.com.au/knowledge?hsLang=en)
2. [PlantOS Mobile App](https://learn.movus.com.au/knowledge/plantos-mobile-app?hsLang=en)
3. [Connect Your Sensors](https://learn.movus.com.au/knowledge/plantos-mobile-app?hsLang=en#connect-your-sensors)

# Check your sensor after setup

## Confirm your sensor is connected and sending data to the correct measurement location.

After adding a sensor, check that setup is complete and monitoring data is available for its assigned measurement location.

The checks differ depending on whether you’re using **FitMachine** or **vEdge/Eqsense**.

### 1. Confirm the setup status

1. Open the **Home Dashboard**.
2. Tap **+ Device**.
3. Select the plant if prompted.
4. Tap **Scan Nearby Sensors**.
5. Find your sensor.

The device card should be **green**, indicating that the sensor is fully configured and actively monitoring.

If it’s blue, amber or yellow, see **Understand sensor setup status** for the next steps.

### 2. Confirm connectivity checks passed

Review the connectivity results during setup.

| Device | Required checks |
| --- | --- |
| **FitMachine** | WLAN, HTTP, HTTPS, SNTP and RSSI |
| **vEdge / Eqsense** | Wi-Fi Connected and Data Streaming Active |

All required checks must pass before onboarding is complete.

If a check fails, confirm the Wi-Fi details, network availability and signal range, then retry.

### 3. Check live communication for vEdge and Eqsense

For **vEdge and Eqsense**, open **Monitor Device** from the setup summary or by tapping the green device card.

This screen uses Bluetooth to retrieve live information directly from the device, so keep your phone nearby with Bluetooth enabled.

**FitMachine users:** Skip this step. FitMachine does not use the same Monitor Device screen.

#### Review device status

The screen displays service indicators for **Sensor**, **Modbus**, **Wi-Fi** and **Data Streaming**.

| Indicator | Meaning |
| --- | --- |
| **Green** | The service is connected and active. |
| **Greyed out** | The service is disconnected, inactive or unavailable. |

Confirm the sensor is on, Wi-Fi is connected and data streaming is active. Some services may not apply to your configuration.

#### Review live readings

Select a monitoring parameter from the dropdown to view its minimum, maximum and average readings.

Available parameters may include:

- Total acceleration
- Velocity
- Temperature
- Other configured sensor parameters

These readings confirm local communication with the sensor. Also check the monitoring views below to confirm data is available against the assigned measurement location.

### 4. Open the assigned measurement location

From the Home Dashboard:

1. Open **Hierarchy** under **Explore Plant**.
2. Select the plant.
3. Open the relevant **Area**.
4. Select the **Equipment**.
5. Select the **Asset**.
6. Open the assigned **Measurement Location**.

Check that the linked device information matches the sensor you’ve just configured.

### 5. Check monitoring data

From the measurement location detail page:

| View | What to check |
| --- | --- |
| **Trends** | Confirm that readings are available for the relevant monitoring parameters. |
| **Spectrum** | Check the available FFT and waveform data for acceleration and velocity. |

Allow **5 to 10 minutes after onboarding** for the first data to arrive.

### Final checklist

Before finishing, confirm:

- The sensor appears green in **Scan Nearby Sensors**.
- All required connectivity checks passed.
- The sensor is linked to the correct measurement location.
- Monitoring data is appearing for that location.
- For vEdge/Eqsense, the applicable live communication indicators are active.

### Need help?

| Issue | What to do |
| --- | --- |
| Sensor appears yellow | Review Wi-Fi settings and retry connectivity checks. |
| Live readings aren’t available on vEdge/Eqsense | Keep your phone close to the sensor and confirm Bluetooth is enabled. Review the service indicators in Monitor Device. |
| Monitoring data hasn’t appeared | Allow 5 to 10 minutes, confirm the linked device and measurement location, then recheck connectivity. |
| Monitor Device isn’t available for FitMachine | Use the setup connectivity results and measurement location monitoring views instead. |

### Related articles

- **Add and configure a sensor**
- **Understand sensor setup status**

- [Partner Resources](https://learn.movus.com.au/knowledge/partner-resources?hsLang=en#main-content)

    - [Start Here](https://learn.movus.com.au/knowledge/partner-resources?hsLang=en#start-here)
    - [Brand Assets](https://learn.movus.com.au/knowledge/partner-resources?hsLang=en#brand-assets)
    - [About MOVUS](https://learn.movus.com.au/knowledge/partner-resources?hsLang=en#about-movus)
    - [Sales & Resources](https://learn.movus.com.au/knowledge/partner-resources?hsLang=en#sales-resources)
- [User Administration](https://learn.movus.com.au/knowledge/user-administration?hsLang=en)
- [PlantOS Mobile App](https://learn.movus.com.au/knowledge/plantos-mobile-app?hsLang=en#main-content)

    - [Getting Started](https://learn.movus.com.au/knowledge/plantos-mobile-app?hsLang=en#getting-started)
    - [Connect Your Sensors](https://learn.movus.com.au/knowledge/plantos-mobile-app?hsLang=en#connect-your-sensors)
    - [Find and Monitor Equipment](https://learn.movus.com.au/knowledge/plantos-mobile-app?hsLang=en#find-and-monitor-equipment)

[![Chill listening crop-3](https://learn.movus.com.au/hs-fs/hubfs/Movus-horizontal-orange-bk-NT.png?width=130&height=20&name=Movus-horizontal-orange-bk-NT.png "Chill listening crop-3")](https://movus.com.au/)

<https://www.youtube.com/channel/UC43yiiOjF3mAhpxI0sB0Wdg> <https://www.linkedin.com/company/movus/>

Copyright © 2026, MOVUS Australia Pty Ltd